Norpak Corporation
EMAIL: info@norpak.ca
TEL: 613-592-4164
FAX: 613-592-6560

NAVE II

Nielsen Audio Video Encoder
 

Overview The NAVE II encoder supports VBI encoding in SMPTE 259 video, VANC encoding in both SMPTE 259 and SMPTE 292 and expands upon Nielsen's audio coding technology by increasing the water-marking capability to 12 AES channels or 16 embedded audio channels. Mixed mode embedded and non-embedded (AES) audio configurations are possible, and the unit can be configured to support up to two simultaneous Dolby 5.1 audio streams. A core part of the familiar "SID" data is carried in the audio to allow SID data to survive VBI-stripping by compression systems and new video formats.

The "SID" (Source Identifier) is a second-by-second serial number used by Nielsen and the television industry to uniquely identify program content to ensure proper crediting of viewing.

The NAVE II is specifically designed for standard and high definition digital plants, with embedded or non-embedded (AES) audio. Possible locations include broadcast television stations (digital and analog), broadcast and cable network operation centers, other program uplink facilities, and other distribution sources delivered to television households. This unit is usually installed in the output chain, after all switching and routing.

The optional captioning software module, which supports EIA-608 VBI captioning in 259 and EIA-708 captioning in both 259 and 292 video, provides a very inexpensive way for users to add HD captioning.

A companion Norpak unit, the Nielsen Universal Reader, will decode and display the SID data to allow users to verify the encoded information.

 
Features SMPTE 259M and 292M Video Interface
AES (12 Channel) or embedded (16 Channel) audio
Applies Nielsen audio and AMOL codes (VBI or VANC)
Front panel go/no-go indicators
Hard relay bypass
No ongoing operator required
1 Rack Unit
Optional DARS input
Code read-back to verify audio and AMOL codes
Optional closed captioning and XDS in VBI (EIA-608) or VANC (EIA-708, SMPTE 334M)
 
Specs

Interface Connections

Video: Digital SD and HD video per SMPTE 259M and SMPTE 292M Serial Digital Interconnect (SDl)

Audio: Six pairs of 75-ohm BNC jacks, providing IN and OUT connections for six AES pairs. Input and output signals are unbalanced, 1V nominal into 75 ohms, and comply with SMPTE 276M. 24 bit resolution at 48K sample rate audio is maintained.

One DARS (AES11-1997) input for optional audio synchronization.

Audio and video terminations are 75 Ohm single ended.

Three serial ports (control, time code, captioning input).

RJ11 and RJ45 Ports for modem and LAN (software updates and configuration).

Contact closure for remote bypass.

Audio/Video Synchronization

Audio and Video are delayed by one frame maintaining proper lip-sync timing. (2 frames for 720p).

Switches

Power On / Off
Bypass / Active
Manual Load

Bypass

SDI and AES paths are protected by Bypass relays that are activated by a front-panel switch, configuration settings, detected fault or loss of power

Indicators

Audio Level channel 1 and 2, Audio Process, and Audio Status for each audio pair
Video Presence
VBI Decode and Encode
VANC Decode and Encode
Serial, LAN and Modem Activity
Bypass Enabled

Power

110V / 60 Hz, 220V / 50 Hz

Size

19"w x 1.72"h x 15"d (48.3 x 4.4 x 38 cm)

Weight

6.4 kg

Environment

Operating Temperature: 32 - 104º F (0 - 40º C)
Storage Temperature: -40 - 149º F (-40 - 65º C)
Humidity: 10 - 90% non-condensing

 

www.norpak.ca © 2010